`gemini get <url>` fetches on a short-lived task (a handshake would trip
the main loop's watchdog; an idle client should cost no stack) and
reports the header, size, certificate fingerprint and heap. First page:
geminiprotocol.net, 20 text/gemini, 1,184 bytes in 0.7-1.1 s.
With IRC connected over TLS, a fetch dips to about 24 KB free during its
handshake, about 36-40 KB after it; nothing leaks. Antenna is down, so
the default aggregator becomes Cosmos.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
custom_sdkconfig makes pioarduino regenerate the ESP-IDF libraries:
asymmetric TLS buffers (16 KB in, 4 KB out) and dynamic buffers that
free handshake-only data once connected. The rebuild also follows the
board: no PSRAM, 8 MB flash. The project now carries the partition
table the hybrid build needs (identical to the framework's: the app
slots must not move under updates over the air). Generated files are
ignored.
Debug Build, GNSS on, IRC on TLS: 78 KB free and a 59 KB low (M2 began
at 31 KB and 12.6 KB; the floor is 40 KB). The full stress set passes
on it: refused installs over Wi-Fi and from SD, put/get, screenshot,
core dump decode, Probation; under all of it at once, the low is 46 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
IrcService::disconnect() stops the session from any state: QUIT if
connected, then no more retries. /quit goes through it (before, it only
stopped a connected session; while waiting for Wi-Fi or retrying it did
nothing), and so does the new `irc stop` command. Stopped by hand,
opening the IRC App no longer reconnects; typing a line does.
mDNS is gone: it never crossed the dev box's routed network, and it
cost about 7.5 KB of RAM. Pushes go to the IP shown in Settings ->
Firmware, which drops its Name row. OTA Q54 records the change.
On the device, Debug Build: 105.6 KB free with Wi-Fi (was 98); with IRC
on TLS 54 KB free (was 46); after `irc stop`, back to 99 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Peak stack use was measured through each task's worst case (an
ECDSA-checked install over Wi-Fi and from SD, get/put, a core dump
fetch, an IRC TLS handshake); stacks are now peak plus about 2 KB: loop
8 -> 6 KB, update 8 -> 5, storage 10 -> 6, irc 8 -> 6. The Debug Build's
console ring goes 6 -> 4 KB, serial TX 2 -> 1 KB, the GNSS UART buffer
1 KB -> 512 B.
On the device, with IRC on TLS: 46 KB free (was 31), an 18 KB low (was
9.4). The re-run of every worst case left at least 1.6 KB of stack free
in each task.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The GNSS Service reads the receiver (UART 15/13, 115200, 1 KB buffer)
from its 50 ms tick and feeds the NMEA parser. With a Fix it sets the
clock (GNSS is the most trusted TimeSource) and refreshes it every 10
min. Settings gets GNSS On/Off and the coordinate format (Q64).
Off puts the receiver in standby with $PCAS12,65535, renewed hourly; On
wakes it with a hot start, $PCAS10,0. Both measured on the device: the
output stops within a second, and a command wakes it within a second.
Commands: gnss status (Fix, satellites per constellation, bytes and
sentences), gnss nmea on|off, gnss send <sentence>, gnss restart. The
probe is gone; never drive GPIO 15 (the receiver's output): the first
probe's swapped-pin attempt silenced it until a power cycle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
A temporary `gnss probe` command listens on both pin orders at 115200
and 9600. Only RX 15 / TX 13 at 115200 carries NMEA, as Meshtastic's
board file says; M5Stack's GPIO 8/9 are the keyboard's I2C bus. The
output format (NMEA 4.10, GSA system IDs, GSV per signal) is recorded in
docs/milestones/M2.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
New commands everywhere: ls, rm and install <path> (Update from SD
without the Firmware page), all as Storage Service jobs. In Debug
Builds the console task answers get and put (one storage job per
transfer, file kept open, TCP flow control: about 300 KB/s, against
55 KB/s over serial) and screenshot (the RGB332 frame the UI composes
into). rdbg.py turns those into files and PNGs.
A failed put closes the connection: the rest of the file had been
parsed as commands. Card writes are retried 3 times after closing,
truncating to the last good byte and reopening, since FATFS keeps a
file in error after one failed write (seen once at 1.3 MB on this card).
onStorage() decides with one compare-and-swap whether the job or the
timeout wins, so an abandoned job can't touch a returned stack frame.
Verified on the device: screenshot; a get round trip byte-identical;
4 puts in a row; a tampered .ota refused by install; a good one put,
installed from SD, confirmed on Probation. The retry path itself has
not fired since it was added.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Every build now records at boot which version runs and, after a crash
restart, which one crashed (even across a Rollback). The core dump
summary (task, PC, reason, backtrace) is printed and raised as a
Notification; `crash` shows it later. After 3 crash restarts in a row
the firmware starts in Safe Mode: clock, Wi-Fi, Update Service and Debug
Console only (SafeMode, 2 host tests). A normal restart or a minute up
resets the count.
The main loop is now on the task watchdog (enableLoopWDT): Arduino only
watched core 0's idle task, so a stuck loop hung the device for good.
The Update Service restarts into an installed update by itself if the
main loop hasn't after 90 s.
Debug Builds: `coredump get` and `reset` are answered by the console's
own task; rdbg.py crash decodes the backtrace and rdbg.py coredump runs
esp-coredump, against ELFs archived by version and digest in .pio/elves.
The StorageService mutex is now made in the constructor: Safe Mode never
starts that Service, and `info` crashed on the null mutex, 29 times in a
row before the fix was pushed into Safe Mode over Wi-Fi.
Verified on the device: crash report and full core dump decoded over
Wi-Fi; Safe Mode at exactly 3 crashes, left by `reboot`; a hung loop
caught by the watchdog in 5 s; `reset` from the console task. ADR 0005.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
cardputer-adv-debug (-DRORO_DEBUG, version +debug) adds a Debug Console:
after a token line, a client gets the last 6 KB of console output, live
lines (ESP-IDF logs included) and the serial commands. The socket task
only queues lines; the main loop runs them. Release builds compile none
of it. The token lives in ~/.config/roro9stack/debug-token, created by
_docker.sh and passed into the container.
All output now goes through `console`, which never waits for USB: a host
that was attached but not reading stalled the main loop up to 2 s per
line. New commands everywhere: info (slots with their versions from NVS,
since the framework stamps its own into each image), tasks, reboot,
boot other, log level, help. scripts/rdbg.py is the client; flash.sh
--debug builds it; CI builds both variants. ADR 0004.
Verified on the device: USB-flashed, then updated over Wi-Fi to a Debug
Build that confirmed on Probation; both slots hold Debug Builds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Verified on the device: a crashing update pushed over Wi-Fi died once,
and the next boot was the previous firmware, with the "Update ... failed"
Toast. bootGuard() stays as a second line.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
A deliberately crashing update looped forever on the device: the
prebuilt bootloader ignores ESP_OTA_IMG_PENDING_VERIFY despite the
app-side rollback config. UpdateService::bootGuard() now runs first in
setup(): it counts starts on Probation in NVS and, on the second
unconfirmed start, marks the image invalid and reboots into the
previous one. Confirming (or the Wi-Fi rollback) resets the counter.
ADR 0003 records the limit: a crash in the first milliseconds still
needs USB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): scan_log (CSV field quoting, header/row, a
once-per-interval throttle) and network_list_view (sort by signal /
channel / name, filter open-only / hide-hidden / strong-only)
- ScanEntry moved to lib/wifi so both are testable on the PC
- Wi-Fi Tools networks view: s sort, o/h/w filters, l toggles logging
to /wifi/scans/<date>.csv (header + one row per AP per logged scan,
throttled 30 s, needs the clock for timestamps); foreground-only
- Wi-Fi scan logs replace probe-request logs as a clean-up category
- Serial: cat <path>, and key <char> injects a character
Verified on the device: CSV written with header, timestamps, BSSID,
channel, RSSI, security and SSID; hidden networks marked.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): channel occupancy (neighbour spill, signal
weighting, quietest of 1/6/11) and a signal tracker (history, lost
detection, click interval)
- WifiService: scan results carry BSSID, channel and security; a scan
can target one channel for quick tracker refreshes; endListScans()
turns the radio back off when Wi-Fi is disabled
- Wi-Fi Tools App: networks nearby, channel occupancy bars, signal
tracker with clicks (m to mute)
- M1 plan: Monitoring-mode views and captures deferred
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
CONTEXT.md captures the roro9stack domain language (Apps, Services,
Mesh Service, Nodes, Channels, Storage rules). ADR 0001 records building
our own firmware that speaks Meshtastic instead of forking it; ADR 0002
records an own widget kit on M5GFX instead of LVGL.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
twislaandClaude Opus 5.5