Enter on a Saved Network opens its page instead of asking to forget it:
"IP address" switches between Automatic and Fixed, with an address, a
prefix and an optional gateway. Fixed starts from what the network is
giving the device; the draft is checked and applied on leaving the page,
so a half-typed address is never used. "DNS and NTP" holds the two DNS
servers, "Always use my DNS" and the two NTP servers. Enter on Status
shows the connection's details and where each value came from. Address
fields take digits and dots only; refusals show as Toasts.
Checked on the device through the screens: Fixed 10.39.39.13 applied and
reverted to Automatic, a prefix of 99 refused. Measurements in
docs/milestones/S1.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The plan and decisions Q105 to Q116 (docs/milestones/S1.md). lib/net:
strict IPv4 parsing, prefix and mask, and the checks a Fixed setting must
pass, each refusal with its reason. A Saved Network is Automatic or Fixed
(address/prefix and an optional gateway), kept with it in flash. Settings:
two DNS servers (9.9.9.9, 1.1.1.1), "Always use my DNS", two NTP servers
(pool.ntp.org, time.cloudflare.com). Host-tested: 383 tests.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Outside, on battery, an hour on LongFast with a Capture running: 0
packets, 0 headers. The noise is no lower than at the desk and its peaks
follow the device, so about 15 dB of the floor is the Cardputer's own
(issue #20). With IRC on TLS and the radio listening, 52.6 KB free. One
"Done when" item is half met: Sweep was never tried against a known
transmitter. The card's refused writes are issue #21.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Tab in the LoRa Scanner sweeps 863-870 MHz in 100 kHz steps (the
strongest of three RSSI readings at each, at 125 kHz), shown as bars with
peak hold over a waterfall, the Sniffer's frequency marked (Q98). The
Sweep pauses the Sniffer and keeps its packets; Tab resumes it (Q99).
Status Bar: SW. The floor, top and peaks are host-tested; `lora sweep
on|off|dump` prints them on the console.
At the desk: about 607 ms a pass, a flat floor at -100 to -102 dBm
(15 dB above the chip's own) and a steady carrier at 863.2 MHz.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The Sniffer lists packets newest first (time, RSSI, SNR, and for
Meshtastic the sender, receiver and hops), with the clear header and a
hex dump on Enter (Q96); `p` picks an EU868 preset, kept in Settings
(Q95). `c` starts a Capture: pcap with LoRaTap in /captures/lora, its own
Clean-up category, recorded by a small Service so it carries on with the
App closed (Q97, Q100). The Status Bar shows L while listening, bright on
each packet, and CAP while capturing (Q101). StorageService gains raw
appends for binary files. Debug Builds get `lora inject` to test all of
this with no transmitter in range: a Capture made on the device reads
back in TShark field for field.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The 16-byte clear header (hops away, channel hash, relay node), the EU_868
presets and their frequency slots, and the channel hash, all checked
against Meshtastic's source. Captures are pcap with LoRaTap v0, read back
with TShark 4.2.5; packet RSSI is plain dBm, as Wireshark reads it.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The probe finds the SX1262 (TCXO 1.8 V works) and measures the antenna
path: the Cap's PI4IOE5V6408 at 0x43 must drive P0 high, or the receiver
is deaf (-111.9 dBm flat vs -87 to -94 dBm with P0 high). DIO2 makes no
difference to reception. Receive only; the radio is left asleep.
RadioLib 7.8.1 + probe: +23.6 KB flash, +656 B static RAM (release).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The Radio Service owns the SX1262 and shares the SPI bus with the card;
the LoRa Scanner shows packets (Sniffer) and the band (Sweep). Nothing in
M3 can transmit. Notes and the File Browser move to issues #19 and #3.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
A page larger than memory allows is now windowed instead of cut: one
pass over its file (cache or Saved Page) counts lines, indexes every
64th (offset, and the preformatted state there in bit 31: about 1 KB
for a 1 MB page) and loads the first window. Scrolling near either end
reads the next or previous window on the Gemini task; the line on top
of the screen stays put, the scrollbar follows the whole page, and Tab
at a window's edge pages on instead of wrapping. Window budgets count
the memory the old window gives back.
Display pages alternate between two cache files so the one on screen
is never overwritten by the next fetch; jobs use a third.
On the device, Cosmos with IRC connected: 226 of 419 lines at first,
then lines 192-419, back to 64 and 0 while scrolling. `key space` added
to the console's key command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Everything touching the network or the card is a job on the Gemini
task (a missing card can block 5 s, past the main loop's watchdog):
about:start is composed from /gemini/bookmarks.gmi and the Saved Pages
(by capsule, newest first); file:// opens a Saved Page; s, S, r, d, b
and downloads report one line to the URL bar, S with progress Toasts.
A Saved Page is the cached body with a first line "> Saved from <url>
on <date>": it shows as a quote and gives relative links their base;
inside one, links to other Saved Pages open the saved copy, others go
online or say "Not saved, and offline". Input prompts (11 masked)
request the same URL with the answer as its query.
Fixed on the way: re-wrapping indented lines rebuilt the text from its
rows, inserting a space where a long word had been cut; refreshing
loaded the whole Saved Page next to a TLS connection (heap down to 436
bytes), now it reads one line and every fetch checks the 55 KB floor.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
GeminiService fetches on a short-lived task and hands the App a
GeminiPage: header, the body as lines in 4 KB chunks (TextBuffer: no
large block, no doubling copies), the final URL after up to 5
redirects. Certificates are pinned on first use per host and port; a
change comes back as its own outcome with both fingerprints. No fetch
starts below 55 KB free (Q86).
With a card, the body streams to /gemini/cache/page.gmi in 1 KB pieces
while the connection is open, then loads into RAM once its memory is
back (Q87); StorageService::runAndWait (moved from the Debug Console)
keeps every card access on the storage task. Without a card: RAM, with
the steady and transient floors.
Measured with IRC connected: Cosmos (31.6 KB) went from 4.6 KB to the
whole page on the card and 20 KB on screen; lowest free heap 19.5 KB
in transfer, 43 KB once loaded. `gemini get` and `gemini trust` on the
console. 14 Gemini tests.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
lib/gemini: URLs split per RFC 3986 appendix B and resolved per section
5.2 (all 32 reference examples of 5.4 pass, with gemini:// for http://),
the request form (no fragment, lower-case host, never an empty path),
query encoding for input prompts, Saved Page paths; the response header
(status, category, MIME type and parameters, 1024-byte meta limit);
gemtext's line types; and display text for the Latin-1 fonts. 12 tests.
Q86, decided after step 1: free heap stays above 40 KB in steady state
and 20 KB during a handshake; a fetch won't start below 55 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
`gemini get <url>` fetches on a short-lived task (a handshake would trip
the main loop's watchdog; an idle client should cost no stack) and
reports the header, size, certificate fingerprint and heap. First page:
geminiprotocol.net, 20 text/gemini, 1,184 bytes in 0.7-1.1 s.
With IRC connected over TLS, a fetch dips to about 24 KB free during its
handshake, about 36-40 KB after it; nothing leaks. Antenna is down, so
the default aggregator becomes Cosmos.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
custom_sdkconfig makes pioarduino regenerate the ESP-IDF libraries:
asymmetric TLS buffers (16 KB in, 4 KB out) and dynamic buffers that
free handshake-only data once connected. The rebuild also follows the
board: no PSRAM, 8 MB flash. The project now carries the partition
table the hybrid build needs (identical to the framework's: the app
slots must not move under updates over the air). Generated files are
ignored.
Debug Build, GNSS on, IRC on TLS: 78 KB free and a 59 KB low (M2 began
at 31 KB and 12.6 KB; the floor is 40 KB). The full stress set passes
on it: refused installs over Wi-Fi and from SD, put/get, screenshot,
core dump decode, Probation; under all of it at once, the low is 46 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
IrcService::disconnect() stops the session from any state: QUIT if
connected, then no more retries. /quit goes through it (before, it only
stopped a connected session; while waiting for Wi-Fi or retrying it did
nothing), and so does the new `irc stop` command. Stopped by hand,
opening the IRC App no longer reconnects; typing a line does.
mDNS is gone: it never crossed the dev box's routed network, and it
cost about 7.5 KB of RAM. Pushes go to the IP shown in Settings ->
Firmware, which drops its Name row. OTA Q54 records the change.
On the device, Debug Build: 105.6 KB free with Wi-Fi (was 98); with IRC
on TLS 54 KB free (was 46); after `irc stop`, back to 99 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Peak stack use was measured through each task's worst case (an
ECDSA-checked install over Wi-Fi and from SD, get/put, a core dump
fetch, an IRC TLS handshake); stacks are now peak plus about 2 KB: loop
8 -> 6 KB, update 8 -> 5, storage 10 -> 6, irc 8 -> 6. The Debug Build's
console ring goes 6 -> 4 KB, serial TX 2 -> 1 KB, the GNSS UART buffer
1 KB -> 512 B.
On the device, with IRC on TLS: 46 KB free (was 31), an 18 KB low (was
9.4). The re-run of every worst case left at least 1.6 KB of stack free
in each task.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The GNSS Service reads the receiver (UART 15/13, 115200, 1 KB buffer)
from its 50 ms tick and feeds the NMEA parser. With a Fix it sets the
clock (GNSS is the most trusted TimeSource) and refreshes it every 10
min. Settings gets GNSS On/Off and the coordinate format (Q64).
Off puts the receiver in standby with $PCAS12,65535, renewed hourly; On
wakes it with a hot start, $PCAS10,0. Both measured on the device: the
output stops within a second, and a command wakes it within a second.
Commands: gnss status (Fix, satellites per constellation, bytes and
sentences), gnss nmea on|off, gnss send <sentence>, gnss restart. The
probe is gone; never drive GPIO 15 (the receiver's output): the first
probe's swapped-pin attempt silenced it until a power cycle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
A temporary `gnss probe` command listens on both pin orders at 115200
and 9600. Only RX 15 / TX 13 at 115200 carries NMEA, as Meshtastic's
board file says; M5Stack's GPIO 8/9 are the keyboard's I2C bus. The
output format (NMEA 4.10, GSA system IDs, GSV per signal) is recorded in
docs/milestones/M2.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): scan_log (CSV field quoting, header/row, a
once-per-interval throttle) and network_list_view (sort by signal /
channel / name, filter open-only / hide-hidden / strong-only)
- ScanEntry moved to lib/wifi so both are testable on the PC
- Wi-Fi Tools networks view: s sort, o/h/w filters, l toggles logging
to /wifi/scans/<date>.csv (header + one row per AP per logged scan,
throttled 30 s, needs the clock for timestamps); foreground-only
- Wi-Fi scan logs replace probe-request logs as a clean-up category
- Serial: cat <path>, and key <char> injects a character
Verified on the device: CSV written with header, timestamps, BSSID,
channel, RSSI, security and SSID; hidden networks marked.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): channel occupancy (neighbour spill, signal
weighting, quietest of 1/6/11) and a signal tracker (history, lost
detection, click interval)
- WifiService: scan results carry BSSID, channel and security; a scan
can target one channel for quick tracker refreshes; endListScans()
turns the radio back off when Wi-Fi is disabled
- Wi-Fi Tools App: networks nearby, channel occupancy bars, signal
tracker with clicks (m to mute)
- M1 plan: Monitoring-mode views and captures deferred
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
twislaandClaude Opus 5.5