At every join the DNS and NTP setup ran twice in the same pass: the
"check now and then" timer compared this pass's time with a stamp taken
from millis() a moment later, and the unsigned difference underflowed.
Starting SNTP is only queued for the network task, so when the second run
looked before the first had been carried out, it queued a second start:
"Operating mode must not be set while SNTP client is running", a panic
nine seconds after boot. Rare (once in the dozen or so boots of this
branch's testing), there since v0.7.0. Rollback caught it: the update
was on Probation and the device went back to the build before.
The service now remembers that it started SNTP instead of asking
esp_sntp_enabled(), and the timer compares signed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Debug Builds: `lora noise test` changes one thing at a time, Sweeps the
band, and reports the floor under each condition; it runs on the device
by itself, since one condition pauses Wi-Fi (not saved, so a restart
brings it back). Result, at 125 kHz: -117 dBm with the antenna switched
off, -106 with the GNSS receiver in standby, -98 with it running. The
receiver's serial line isn't it (one sentence a second changes nothing),
and neither are the main loop, the CPU frequency, Wi-Fi, the screen or
the radio's own regulator, all within 1 dB.
Settings > "Pause GNSS for LoRa", off by default: the receiver waits in
standby while the radio listens or sweeps, except during a Track, and
has a Fix again about 7 s after. The GNSS App says it's paused.
11 dB remain between the antenna with GNSS quiet and the chip alone,
untouched by anything that can be switched from the firmware.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Joining a Saved Network uses its Fixed address, mask and gateway, or
DHCP. DNS comes from Settings on Fixed networks and when "Always use my
DNS" is on; NTP servers come from Settings, after any that DHCP offered.
Both are re-checked every 30 s, since a DHCP renewal puts DHCP's DNS back
and clears the NTP slots it didn't fill. `wifi status` shows what's in
use, where it came from, and which NTP servers answered; `wifi ip`,
`wifi dns`, `wifi ntp`. Debug Builds: `wifi ip ... try <s>` reverts
unless kept.
On knbg-guests (10.39.39.0/24, gateway .1): Fixed .12 and .13 both reach
the internet through 9.9.9.9; a wrong gateway on trial cut the device off
and came back by itself; back to DHCP; both NTP servers answer.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- EcdsaVerifier (mbedTLS, embedded public key) and EspOtaSink (writes
the inactive app slot, esp_ota_end validates the image, then sets
the boot partition)
- UpdateService: listens on TCP 3232 (and mDNS roro9stack-<id>) while
Wi-Fi is Connected; streams into UpdateParser; replies OK/ERR to the
sender; remembers the pending version so a Rollback is reported
after the reboot
- Probation (host-tested): confirm after the first frame + 30 s + Wi-Fi
(if configured); roll back if configured Wi-Fi never connects in 3 min
- Main loop: full-screen progress while receiving; restart once
installed, waiting up to 60 s for Text Entry to end
- Settings > Firmware: version, Probation status, push address and
name, and the .ota files in /updates on the SD card to install
- StorageService.runJob() runs work on the storage task (SD installs)
- wifi status prints IP and running version; RORO_TEST_CRASH test hook
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): scan_log (CSV field quoting, header/row, a
once-per-interval throttle) and network_list_view (sort by signal /
channel / name, filter open-only / hide-hidden / strong-only)
- ScanEntry moved to lib/wifi so both are testable on the PC
- Wi-Fi Tools networks view: s sort, o/h/w filters, l toggles logging
to /wifi/scans/<date>.csv (header + one row per AP per logged scan,
throttled 30 s, needs the clock for timestamps); foreground-only
- Wi-Fi scan logs replace probe-request logs as a clean-up category
- Serial: cat <path>, and key <char> injects a character
Verified on the device: CSV written with header, timestamps, BSSID,
channel, RSSI, security and SSID; hidden networks marked.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): channel occupancy (neighbour spill, signal
weighting, quietest of 1/6/11) and a signal tracker (history, lost
detection, click interval)
- WifiService: scan results carry BSSID, channel and security; a scan
can target one channel for quick tracker refreshes; endListScans()
turns the radio back off when Wi-Fi is disabled
- Wi-Fi Tools App: networks nearby, channel occupancy bars, signal
tracker with clicks (m to mute)
- M1 plan: Monitoring-mode views and captures deferred
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): SavedNetworks (up to 8, validated, hidden
flag, persisted) and WifiController (joins the strongest Saved
Network, tries hidden ones in turn, backoff 10/30/60 s, connect
timeout, Monitoring override, radio off without Saved Networks)
- WifiService carries out the controller's actions, sets the EU
country code, and syncs the Clock over SNTP without touching the TZ
- Wi-Fi On/Off setting; Settings > Wi-Fi page: status, add from a scan
or a hidden network, forget
- Status Bar: W + signal bars, W? while searching, MON while monitoring
- Serial: wifi add / wifi status (replaces the step 1 heap probe)
Verified on the device: joins the test network ~5 s after boot, clock
set over NTP, ~129 KB free heap while connected.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
twislaandClaude Opus 5.5