custom_sdkconfig makes pioarduino regenerate the ESP-IDF libraries:
asymmetric TLS buffers (16 KB in, 4 KB out) and dynamic buffers that
free handshake-only data once connected. The rebuild also follows the
board: no PSRAM, 8 MB flash. The project now carries the partition
table the hybrid build needs (identical to the framework's: the app
slots must not move under updates over the air). Generated files are
ignored.
Debug Build, GNSS on, IRC on TLS: 78 KB free and a 59 KB low (M2 began
at 31 KB and 12.6 KB; the floor is 40 KB). The full stress set passes
on it: refused installs over Wi-Fi and from SD, put/get, screenshot,
core dump decode, Probation; under all of it at once, the low is 46 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
IrcService::disconnect() stops the session from any state: QUIT if
connected, then no more retries. /quit goes through it (before, it only
stopped a connected session; while waiting for Wi-Fi or retrying it did
nothing), and so does the new `irc stop` command. Stopped by hand,
opening the IRC App no longer reconnects; typing a line does.
mDNS is gone: it never crossed the dev box's routed network, and it
cost about 7.5 KB of RAM. Pushes go to the IP shown in Settings ->
Firmware, which drops its Name row. OTA Q54 records the change.
On the device, Debug Build: 105.6 KB free with Wi-Fi (was 98); with IRC
on TLS 54 KB free (was 46); after `irc stop`, back to 99 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Peak stack use was measured through each task's worst case (an
ECDSA-checked install over Wi-Fi and from SD, get/put, a core dump
fetch, an IRC TLS handshake); stacks are now peak plus about 2 KB: loop
8 -> 6 KB, update 8 -> 5, storage 10 -> 6, irc 8 -> 6. The Debug Build's
console ring goes 6 -> 4 KB, serial TX 2 -> 1 KB, the GNSS UART buffer
1 KB -> 512 B.
On the device, with IRC on TLS: 46 KB free (was 31), an 18 KB low (was
9.4). The re-run of every worst case left at least 1.6 KB of stack free
in each task.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The GNSS Service reads the receiver (UART 15/13, 115200, 1 KB buffer)
from its 50 ms tick and feeds the NMEA parser. With a Fix it sets the
clock (GNSS is the most trusted TimeSource) and refreshes it every 10
min. Settings gets GNSS On/Off and the coordinate format (Q64).
Off puts the receiver in standby with $PCAS12,65535, renewed hourly; On
wakes it with a hot start, $PCAS10,0. Both measured on the device: the
output stops within a second, and a command wakes it within a second.
Commands: gnss status (Fix, satellites per constellation, bytes and
sentences), gnss nmea on|off, gnss send <sentence>, gnss restart. The
probe is gone; never drive GPIO 15 (the receiver's output): the first
probe's swapped-pin attempt silenced it until a power cycle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
A temporary `gnss probe` command listens on both pin orders at 115200
and 9600. Only RX 15 / TX 13 at 115200 carries NMEA, as Meshtastic's
board file says; M5Stack's GPIO 8/9 are the keyboard's I2C bus. The
output format (NMEA 4.10, GSA system IDs, GSV per signal) is recorded in
docs/milestones/M2.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): scan_log (CSV field quoting, header/row, a
once-per-interval throttle) and network_list_view (sort by signal /
channel / name, filter open-only / hide-hidden / strong-only)
- ScanEntry moved to lib/wifi so both are testable on the PC
- Wi-Fi Tools networks view: s sort, o/h/w filters, l toggles logging
to /wifi/scans/<date>.csv (header + one row per AP per logged scan,
throttled 30 s, needs the clock for timestamps); foreground-only
- Wi-Fi scan logs replace probe-request logs as a clean-up category
- Serial: cat <path>, and key <char> injects a character
Verified on the device: CSV written with header, timestamps, BSSID,
channel, RSSI, security and SSID; hidden networks marked.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): channel occupancy (neighbour spill, signal
weighting, quietest of 1/6/11) and a signal tracker (history, lost
detection, click interval)
- WifiService: scan results carry BSSID, channel and security; a scan
can target one channel for quick tracker refreshes; endListScans()
turns the radio back off when Wi-Fi is disabled
- Wi-Fi Tools App: networks nearby, channel occupancy bars, signal
tracker with clicks (m to mute)
- M1 plan: Monitoring-mode views and captures deferred
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
twislaandClaude Opus 5.5