Tab in the LoRa Scanner sweeps 863-870 MHz in 100 kHz steps (the
strongest of three RSSI readings at each, at 125 kHz), shown as bars with
peak hold over a waterfall, the Sniffer's frequency marked (Q98). The
Sweep pauses the Sniffer and keeps its packets; Tab resumes it (Q99).
Status Bar: SW. The floor, top and peaks are host-tested; `lora sweep
on|off|dump` prints them on the console.
At the desk: about 607 ms a pass, a flat floor at -100 to -102 dBm
(15 dB above the chip's own) and a steady carrier at 863.2 MHz.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The Sniffer lists packets newest first (time, RSSI, SNR, and for
Meshtastic the sender, receiver and hops), with the clear header and a
hex dump on Enter (Q96); `p` picks an EU868 preset, kept in Settings
(Q95). `c` starts a Capture: pcap with LoRaTap in /captures/lora, its own
Clean-up category, recorded by a small Service so it carries on with the
App closed (Q97, Q100). The Status Bar shows L while listening, bright on
each packet, and CAP while capturing (Q101). StorageService gains raw
appends for binary files. Debug Builds get `lora inject` to test all of
this with no transmitter in range: a Capture made on the device reads
back in TShark field for field.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
`r` in the GNSS App (or `gnss track start|stop`) records a Track to
/gnss/tracks/YYYYMMDD-HHMMSS.gpx: a point every 5 s once moved 5 m
(lib/gnss/track, 7 tests: haversine, the rule, GPX text, the file name).
It keeps recording with the App closed, shows REC in the Status Bar, and
announces start and stop with a Toast. It needs a card and the time;
switching GNSS off stops it. Tracks are written like Captures: past 90 %
card usage, until full. Storage Clean-up gets a GNSS tracks category.
A Track cut short by a reset or power loss has no GPX footer; the GNSS
Service closes such files at the next boot.
Verified on the device: a recorded Track and one interrupted by a reset
both parse as GPX 1.1 on the PC.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Q61: a muted G while searching (or the receiver is silent), G with a 2D
Fix, G and the satellite count with a 3D Fix; nothing when GNSS is off.
Verified on the device by a window: 3D Fix, 9 of 11 satellites used
(GPS, GLONASS, BeiDou), HDOP 1.3, Status Bar "G9", and "gnss: clock set".
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- EcdsaVerifier (mbedTLS, embedded public key) and EspOtaSink (writes
the inactive app slot, esp_ota_end validates the image, then sets
the boot partition)
- UpdateService: listens on TCP 3232 (and mDNS roro9stack-<id>) while
Wi-Fi is Connected; streams into UpdateParser; replies OK/ERR to the
sender; remembers the pending version so a Rollback is reported
after the reboot
- Probation (host-tested): confirm after the first frame + 30 s + Wi-Fi
(if configured); roll back if configured Wi-Fi never connects in 3 min
- Main loop: full-screen progress while receiving; restart once
installed, waiting up to 60 s for Text Entry to end
- Settings > Firmware: version, Probation status, push address and
name, and the .ota files in /updates on the SD card to install
- StorageService.runJob() runs work on the storage task (SD installs)
- wifi status prints IP and running version; RORO_TEST_CRASH test hook
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- IrcService: networking on its own task, TLS with the built-in CA
bundle (or trust-on-first-use pinning when self-signed is allowed),
plain TCP when TLS is off; connects only while Wi-Fi is Connected,
marks pauses for Monitoring, reconnects with backoff, pings a quiet
server, writes Logs, raises Notifications for Mentions
- Session: forget /quit once disconnected (it was handled every loop);
the server Buffer never counts as unread (MOTD showed as [4])
- Status Bar: unread count
- Frame buffer 16 -> 8-bit colour (M1 Q46): min free heap with IRC on
TLS went from 51 KB to 79 KB
- Serial: irc start / say / dump
Verified on the device against irc.libera.chat:6697: certificate
checked, joined #roro9stack-test, sent a message, quit cleanly.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): SavedNetworks (up to 8, validated, hidden
flag, persisted) and WifiController (joins the strongest Saved
Network, tries hidden ones in turn, backoff 10/30/60 s, connect
timeout, Monitoring override, radio off without Saved Networks)
- WifiService carries out the controller's actions, sets the EU
country code, and syncs the Clock over SNTP without touching the TZ
- Wi-Fi On/Off setting; Settings > Wi-Fi page: status, add from a scan
or a hidden network, forget
- Status Bar: W + signal bars, W? while searching, MON while monitoring
- Serial: wifi add / wifi status (replaces the step 1 heap probe)
Verified on the device: joins the test network ~5 s after boot, clock
set over NTP, ~129 KB free heap while connected.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/apps_model (host-tested): SettingsMenu (rows, readable values,
choices, validation messages) and SetupWizard (names, Region
confirmation, timezone; saves only when finished)
- AppManager: modal Apps that Home/Back can't leave (setup wizard)
- SettingsApp: all settings plus Storage (usage, erase SD behind a
dialog) and About (version, node id, battery, memory, uptime) pages,
replacing the temporary Diagnostics App
- SetupApp: first-boot wizard, opened modally until SetupDone
- Node id and default names derived from the MAC like Meshtastic
- Widget demo is now hidden (About, then w)
- lib_ldf_mode = deep+ so libraries see each other's headers
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
An Off screen turns on dimmed for the Toast's duration so the user can
see what beeped. It isn't user activity: the timeouts aren't restarted,
and a key pressed meanwhile reaches the App.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- ToastQueue compared times unsigned: a Toast stamped a few ms after the
main loop read the clock looked expired, so Toasts were skipped or
shown late and bursts chained wrongly
- Notifier now beeps and flashes when each Toast appears instead of when
the Notification arrives, so a burst alerts once per Toast
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
twislaandClaude Opus 5.5