A Counted<> wrapper around the network clients adds what goes through
their buffer read and write to a per-service counter (IRC, Gemini, Debug
Console, Updates); the single-byte calls and print() end up there, so
each byte counts once. `net` prints the totals. For TLS it's the plain
text the service sees.
Checked on the device: a Gemini fetch counts 164,986 in (a 164,970-byte
page and its 16-byte header) and 42 out (the URL and CRLF).
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
IrcService::disconnect() stops the session from any state: QUIT if
connected, then no more retries. /quit goes through it (before, it only
stopped a connected session; while waiting for Wi-Fi or retrying it did
nothing), and so does the new `irc stop` command. Stopped by hand,
opening the IRC App no longer reconnects; typing a line does.
mDNS is gone: it never crossed the dev box's routed network, and it
cost about 7.5 KB of RAM. Pushes go to the IP shown in Settings ->
Firmware, which drops its Name row. OTA Q54 records the change.
On the device, Debug Build: 105.6 KB free with Wi-Fi (was 98); with IRC
on TLS 54 KB free (was 46); after `irc stop`, back to 99 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Peak stack use was measured through each task's worst case (an
ECDSA-checked install over Wi-Fi and from SD, get/put, a core dump
fetch, an IRC TLS handshake); stacks are now peak plus about 2 KB: loop
8 -> 6 KB, update 8 -> 5, storage 10 -> 6, irc 8 -> 6. The Debug Build's
console ring goes 6 -> 4 KB, serial TX 2 -> 1 KB, the GNSS UART buffer
1 KB -> 512 B.
On the device, with IRC on TLS: 46 KB free (was 31), an 18 KB low (was
9.4). The re-run of every worst case left at least 1.6 KB of stack free
in each task.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Every build now records at boot which version runs and, after a crash
restart, which one crashed (even across a Rollback). The core dump
summary (task, PC, reason, backtrace) is printed and raised as a
Notification; `crash` shows it later. After 3 crash restarts in a row
the firmware starts in Safe Mode: clock, Wi-Fi, Update Service and Debug
Console only (SafeMode, 2 host tests). A normal restart or a minute up
resets the count.
The main loop is now on the task watchdog (enableLoopWDT): Arduino only
watched core 0's idle task, so a stuck loop hung the device for good.
The Update Service restarts into an installed update by itself if the
main loop hasn't after 90 s.
Debug Builds: `coredump get` and `reset` are answered by the console's
own task; rdbg.py crash decodes the backtrace and rdbg.py coredump runs
esp-coredump, against ELFs archived by version and digest in .pio/elves.
The StorageService mutex is now made in the constructor: Safe Mode never
starts that Service, and `info` crashed on the null mutex, 29 times in a
row before the fix was pushed into Safe Mode over Wi-Fi.
Verified on the device: crash report and full core dump decoded over
Wi-Fi; Safe Mode at exactly 3 crashes, left by `reboot`; a hung loop
caught by the watchdog in 5 s; `reset` from the console task. ADR 0005.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
cardputer-adv-debug (-DRORO_DEBUG, version +debug) adds a Debug Console:
after a token line, a client gets the last 6 KB of console output, live
lines (ESP-IDF logs included) and the serial commands. The socket task
only queues lines; the main loop runs them. Release builds compile none
of it. The token lives in ~/.config/roro9stack/debug-token, created by
_docker.sh and passed into the container.
All output now goes through `console`, which never waits for USB: a host
that was attached but not reading stalled the main loop up to 2 s per
line. New commands everywhere: info (slots with their versions from NVS,
since the framework stamps its own into each image), tasks, reboot,
boot other, log level, help. scripts/rdbg.py is the client; flash.sh
--debug builds it; CI builds both variants. ADR 0004.
Verified on the device: USB-flashed, then updated over Wi-Fi to a Debug
Build that confirmed on Probation; both slots hold Debug Builds.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
A deliberately crashing update looped forever on the device: the
prebuilt bootloader ignores ESP_OTA_IMG_PENDING_VERIFY despite the
app-side rollback config. UpdateService::bootGuard() now runs first in
setup(): it counts starts on Probation in NVS and, on the second
unconfirmed start, marks the image invalid and reboots into the
previous one. Confirming (or the Wi-Fi rollback) resets the counter.
ADR 0003 records the limit: a crash in the first milliseconds still
needs USB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The Arduino network client treats a half-closed connection as closed,
so the device's reply after the sender's EOF was lost. The header
already carries the image size: UpdateParser::complete() lets the
device finish and answer while the connection is open. ota_push.py
half-closes only if no answer comes within 3 s, for older firmware.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- EcdsaVerifier (mbedTLS, embedded public key) and EspOtaSink (writes
the inactive app slot, esp_ota_end validates the image, then sets
the boot partition)
- UpdateService: listens on TCP 3232 (and mDNS roro9stack-<id>) while
Wi-Fi is Connected; streams into UpdateParser; replies OK/ERR to the
sender; remembers the pending version so a Rollback is reported
after the reboot
- Probation (host-tested): confirm after the first frame + 30 s + Wi-Fi
(if configured); roll back if configured Wi-Fi never connects in 3 min
- Main loop: full-screen progress while receiving; restart once
installed, waiting up to 60 s for Text Entry to end
- Settings > Firmware: version, Probation status, push address and
name, and the .ota files in /updates on the SD card to install
- StorageService.runJob() runs work on the storage task (SD installs)
- wifi status prints IP and running version; RORO_TEST_CRASH test hook
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
twislaandClaude Opus 5.5