The roots (ISRG X1 and X2), an HTTPS client that reads the answer as a
stream, GiteaReleases (the latest and a list of ten), the Update
Service's requests, install from Gitea through the existing install path,
the daily check's schedule, the Check for updates setting, and console
commands: update check | list | status | install <tag>.
Co-Authored-By: Claude Sonnet 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The Storage App browses the SD card: folders first with sizes and dates,
three sorts, one item at a time with a clipboard (c, x, v), rename, delete
after counting what's inside, new folder, details. A listing holds 256
entries and says when a folder has more.
FileOps does the card's work for the App and the console alike, one
operation at a time on the storage task in turns of about 150 ms, so Logs
and Captures are still written during a long copy. A copy shows progress,
can be cancelled (what it wrote is taken back) and compares sizes after.
The read-only rules are checked there: the firmware's top-level folders,
/gemini/cache, and files being written (a Track, a Capture, an upload,
today's IRC Logs). A listing reads the folder straight from FatFs: through
the Arduino File, 329 entries took over two seconds.
Viewers by type: text read a screen at a time whatever the file's size
(logs open at the end), a hex dump, a Capture's packets as the LoRa Scanner
lists them, a Track's summary, and an Update File checked as an install
would check it, without writing anything. Tab shows any file as hex or text.
Settings > Storage is gone: usage, Storage Clean-up and Erase are the App's
Maintenance, behind a warning. The Storage Warning points there.
The Clock sets the system time whatever its source, so files are dated
correctly with a GNSS Fix alone (Q137).
Console: cp, mv, mkdir, du, cancel; rm takes folders and follows the rules;
ls shows dates; Debug Builds get `sd fill`.
424 host tests. Checked on the device: docs/milestones/F1.md.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Debug Builds: `lora noise test` changes one thing at a time, Sweeps the
band, and reports the floor under each condition; it runs on the device
by itself, since one condition pauses Wi-Fi (not saved, so a restart
brings it back). Result, at 125 kHz: -117 dBm with the antenna switched
off, -106 with the GNSS receiver in standby, -98 with it running. The
receiver's serial line isn't it (one sentence a second changes nothing),
and neither are the main loop, the CPU frequency, Wi-Fi, the screen or
the radio's own regulator, all within 1 dB.
Settings > "Pause GNSS for LoRa", off by default: the receiver waits in
standby while the radio listens or sweeps, except during a Track, and
has a Fix again about 7 s after. The GNSS App says it's paused.
11 dB remain between the antenna with GNSS quiet and the chip alone,
untouched by anything that can be switched from the firmware.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The GNSS Service reads the receiver (UART 15/13, 115200, 1 KB buffer)
from its 50 ms tick and feeds the NMEA parser. With a Fix it sets the
clock (GNSS is the most trusted TimeSource) and refreshes it every 10
min. Settings gets GNSS On/Off and the coordinate format (Q64).
Off puts the receiver in standby with $PCAS12,65535, renewed hourly; On
wakes it with a hot start, $PCAS10,0. Both measured on the device: the
output stops within a second, and a command wakes it within a second.
Commands: gnss status (Fix, satellites per constellation, bytes and
sentences), gnss nmea on|off, gnss send <sentence>, gnss restart. The
probe is gone; never drive GPIO 15 (the receiver's output): the first
probe's swapped-pin attempt silenced it until a power cycle.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- EcdsaVerifier (mbedTLS, embedded public key) and EspOtaSink (writes
the inactive app slot, esp_ota_end validates the image, then sets
the boot partition)
- UpdateService: listens on TCP 3232 (and mDNS roro9stack-<id>) while
Wi-Fi is Connected; streams into UpdateParser; replies OK/ERR to the
sender; remembers the pending version so a Rollback is reported
after the reboot
- Probation (host-tested): confirm after the first frame + 30 s + Wi-Fi
(if configured); roll back if configured Wi-Fi never connects in 3 min
- Main loop: full-screen progress while receiving; restart once
installed, waiting up to 60 s for Text Entry to end
- Settings > Firmware: version, Probation status, push address and
name, and the .ota files in /updates on the SD card to install
- StorageService.runJob() runs work on the storage task (SD installs)
- wifi status prints IP and running version; RORO_TEST_CRASH test hook
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): SavedNetworks (up to 8, validated, hidden
flag, persisted) and WifiController (joins the strongest Saved
Network, tries hidden ones in turn, backoff 10/30/60 s, connect
timeout, Monitoring override, radio off without Saved Networks)
- WifiService carries out the controller's actions, sets the EU
country code, and syncs the Clock over SNTP without touching the TZ
- Wi-Fi On/Off setting; Settings > Wi-Fi page: status, add from a scan
or a hidden network, forget
- Status Bar: W + signal bars, W? while searching, MON while monitoring
- Serial: wifi add / wifi status (replaces the step 1 heap probe)
Verified on the device: joins the test network ~5 s after boot, clock
set over NTP, ~129 KB free heap while connected.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/apps_model (host-tested): SettingsMenu (rows, readable values,
choices, validation messages) and SetupWizard (names, Region
confirmation, timezone; saves only when finished)
- AppManager: modal Apps that Home/Back can't leave (setup wizard)
- SettingsApp: all settings plus Storage (usage, erase SD behind a
dialog) and About (version, node id, battery, memory, uptime) pages,
replacing the temporary Diagnostics App
- SetupApp: first-boot wizard, opened modally until SetupDone
- Node id and default names derived from the MAC like Meshtastic
- Widget demo is now hidden (About, then w)
- lib_ldf_mode = deep+ so libraries see each other's headers
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
twislaandClaude Sonnet 5.5