Tab in the LoRa Scanner sweeps 863-870 MHz in 100 kHz steps (the
strongest of three RSSI readings at each, at 125 kHz), shown as bars with
peak hold over a waterfall, the Sniffer's frequency marked (Q98). The
Sweep pauses the Sniffer and keeps its packets; Tab resumes it (Q99).
Status Bar: SW. The floor, top and peaks are host-tested; `lora sweep
on|off|dump` prints them on the console.
At the desk: about 607 ms a pass, a flat floor at -100 to -102 dBm
(15 dB above the chip's own) and a steady carrier at 863.2 MHz.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The Sniffer lists packets newest first (time, RSSI, SNR, and for
Meshtastic the sender, receiver and hops), with the clear header and a
hex dump on Enter (Q96); `p` picks an EU868 preset, kept in Settings
(Q95). `c` starts a Capture: pcap with LoRaTap in /captures/lora, its own
Clean-up category, recorded by a small Service so it carries on with the
App closed (Q97, Q100). The Status Bar shows L while listening, bright on
each packet, and CAP while capturing (Q101). StorageService gains raw
appends for binary files. Debug Builds get `lora inject` to test all of
this with no transmitter in range: a Capture made on the device reads
back in TShark field for field.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Found in M3 while checking floors with the radio on: a windowed page left
1.5 to 3 KB less than the 40 KB steady floor (Q86), radio or not. The
budget counted TextBuffer's index (8 B/line) but not the App's tables,
which also grew by doubling. Now 16 B/line, and the App sizes them
exactly. The FAQ (1051 lines, windowed): 38.5 -> 39.6 KB after, radio
asleep; 37.1 -> 39.0 KB with the radio listening.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
A page larger than memory allows is now windowed instead of cut: one
pass over its file (cache or Saved Page) counts lines, indexes every
64th (offset, and the preformatted state there in bit 31: about 1 KB
for a 1 MB page) and loads the first window. Scrolling near either end
reads the next or previous window on the Gemini task; the line on top
of the screen stays put, the scrollbar follows the whole page, and Tab
at a window's edge pages on instead of wrapping. Window budgets count
the memory the old window gives back.
Display pages alternate between two cache files so the one on screen
is never overwritten by the next fetch; jobs use a third.
On the device, Cosmos with IRC connected: 226 of 419 lines at first,
then lines 192-419, back to 64 and 0 while scrolling. `key space` added
to the console's key command.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Everything touching the network or the card is a job on the Gemini
task (a missing card can block 5 s, past the main loop's watchdog):
about:start is composed from /gemini/bookmarks.gmi and the Saved Pages
(by capsule, newest first); file:// opens a Saved Page; s, S, r, d, b
and downloads report one line to the URL bar, S with progress Toasts.
A Saved Page is the cached body with a first line "> Saved from <url>
on <date>": it shows as a quote and gives relative links their base;
inside one, links to other Saved Pages open the saved copy, others go
online or say "Not saved, and offline". Input prompts (11 masked)
request the same URL with the answer as its query.
Fixed on the way: re-wrapping indented lines rebuilt the text from its
rows, inserting a space where a long word had been cut; refreshing
loaded the whole Saved Page next to a TLS connection (heap down to 436
bytes), now it reads one line and every fetch checks the 55 KB floor.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Gemtext as Q75 has it: headings bold (# in the accent colour), lists
with a middle dot, quotes muted, links as » labels, preformatted lines
unwrapped and scrolled sideways together; other text/* as is. Pages are
wrapped once for each line's first row (4 bytes a line) and only the
lines on screen are wrapped again to draw. Tab and Shift+Tab move
between links, Enter follows (relative links resolved), Back or Delete
go back to where the page was scrolled, g opens the address line.
Non-Gemini links say so in the URL bar; a changed certificate opens a
dialog; errors and refusals get a page with a "Try again" link; a page
only partly in memory says why at its end.
A status message timed with millis() after the loop's clock read was
cleared before it was drawn (unsigned wrap): now a signed comparison,
as for the toasts in M0.
Verified on the device: start page, Project Gemini, its relative news/
link, Back with the scroll restored, and the YouTube link refused.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
IrcService::disconnect() stops the session from any state: QUIT if
connected, then no more retries. /quit goes through it (before, it only
stopped a connected session; while waiting for Wi-Fi or retrying it did
nothing), and so does the new `irc stop` command. Stopped by hand,
opening the IRC App no longer reconnects; typing a line does.
mDNS is gone: it never crossed the dev box's routed network, and it
cost about 7.5 KB of RAM. Pushes go to the IP shown in Settings ->
Firmware, which drops its Name row. OTA Q54 records the change.
On the device, Debug Build: 105.6 KB free with Wi-Fi (was 98); with IRC
on TLS 54 KB free (was 46); after `irc stop`, back to 99 KB.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
`r` in the GNSS App (or `gnss track start|stop`) records a Track to
/gnss/tracks/YYYYMMDD-HHMMSS.gpx: a point every 5 s once moved 5 m
(lib/gnss/track, 7 tests: haversine, the rule, GPX text, the file name).
It keeps recording with the App closed, shows REC in the Status Bar, and
announces start and stop with a Toast. It needs a card and the time;
switching GNSS off stops it. Tracks are written like Captures: past 90 %
card usage, until full. Storage Clean-up gets a GNSS tracks category.
A Track cut short by a reset or power loss has no GPX footer; the GNSS
Service closes such files at the next boot.
Verified on the device: a recorded Track and one interrupted by a reset
both parse as GPX 1.1 on the PC.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
Position: the Fix line (or how long it has been searching), latitude and
longitude in decimal degrees or degrees-minutes-seconds (Settings ->
Coordinates), the Maidenhead locator, altitude, speed and course, HDOP
and UTC. Sky: the satellites by azimuth and elevation, coloured by
constellation, filled when used in the Fix, with used/in-view counts.
Tab switches. lib/gnss/geo_format holds the formatting, the locator and
the sky projection, host-tested (6 tests; locators checked against
FN31pr and JN58td).
Verified on the device by a window: 3D Fix from GPS, GLONASS, Galileo
and BeiDou.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- EcdsaVerifier (mbedTLS, embedded public key) and EspOtaSink (writes
the inactive app slot, esp_ota_end validates the image, then sets
the boot partition)
- UpdateService: listens on TCP 3232 (and mDNS roro9stack-<id>) while
Wi-Fi is Connected; streams into UpdateParser; replies OK/ERR to the
sender; remembers the pending version so a Rollback is reported
after the reboot
- Probation (host-tested): confirm after the first frame + 30 s + Wi-Fi
(if configured); roll back if configured Wi-Fi never connects in 3 min
- Main loop: full-screen progress while receiving; restart once
installed, waiting up to 60 s for Text Entry to end
- Settings > Firmware: version, Probation status, push address and
name, and the .ota files in /updates on the SD card to install
- StorageService.runJob() runs work on the storage task (SD installs)
- wifi status prints IP and running version; RORO_TEST_CRASH test hook
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): scan_log (CSV field quoting, header/row, a
once-per-interval throttle) and network_list_view (sort by signal /
channel / name, filter open-only / hide-hidden / strong-only)
- ScanEntry moved to lib/wifi so both are testable on the PC
- Wi-Fi Tools networks view: s sort, o/h/w filters, l toggles logging
to /wifi/scans/<date>.csv (header + one row per AP per logged scan,
throttled 30 s, needs the clock for timestamps); foreground-only
- Wi-Fi scan logs replace probe-request logs as a clean-up category
- Serial: cat <path>, and key <char> injects a character
Verified on the device: CSV written with header, timestamps, BSSID,
channel, RSSI, security and SSID; hidden networks marked.
Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- Alt + ; / Alt + . scroll the Buffer back and forward
- Up / Down (Fn + ; / Fn + .) browse the last 30 sent lines, shell-style,
returning to the draft past the newest (InputHistory, host-tested)
- /j is short for /join
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- With NickServ, auto-join waits for the logged-in reply (900) or 2 s
at most, so registered-only IRC channels let us in
- A failed SASL login falls back to NickServ (its own password, or the
SASL account and password)
- IDENTIFY names the account explicitly, and once logged in on a
fallback nick, REGAIN takes ours back from a stale session
- Auto-join entries take keys ("#private key, #public"); keys from
/join are reused when rejoining; keyed channels go first in JOIN
- Serial irc dump: whole Buffers, and which login is configured
(never the secrets)
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
The IRC App edited the live config while the IRC task could be reading
it to connect. The App now edits a copy; applyConfig() validates it and
swaps it in under the lock, and the task connects from a snapshot.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): channel occupancy (neighbour spill, signal
weighting, quietest of 1/6/11) and a signal tracker (history, lost
detection, click interval)
- WifiService: scan results carry BSSID, channel and security; a scan
can target one channel for quick tracker refreshes; endListScans()
turns the radio back off when Wi-Fi is disabled
- Wi-Fi Tools App: networks nearby, channel occupancy bars, signal
tracker with clicks (m to mute)
- M1 plan: Monitoring-mode views and captures deferred
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- Chat: header (Buffer n/N, unread elsewhere, topic or connection
state), wrapped hh:mm <nick> lines (own in accent, Mentions green,
info grey), input line; Tab cycles Buffers, Fn+Up/Down scrolls back,
Enter sends, Back leaves while the IRC Service keeps running
- /settings: server form (host, port, TLS, self-signed pinning, nick,
SASL, NickServ, auto-join); Save & reconnect restarts the session
- Opening the App starts the IRC Service; viewing a Buffer clears its
unread count; IrcSession gains a revision counter for redraws
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/storage_model (host-tested): FAT-safe names, daily Log paths,
dates from Log/Capture file names, CleanupPlan by category and age,
byte formatting
- StorageService does all card I/O on its task: queued Log lines are
written in batches each second (dropped while Logs are paused),
plus file listing and deletion jobs
- Settings > Storage moves into StoragePage: usage, Clean up
(category, age with size preview, confirmation), Erase SD card
- Clock: local date for Log names
- Serial: log <text>, sd list
Verified on the device: lines land in /irc/dev/#test/2026-10-02.log
with folders created as needed.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/wifi (host-tested): SavedNetworks (up to 8, validated, hidden
flag, persisted) and WifiController (joins the strongest Saved
Network, tries hidden ones in turn, backoff 10/30/60 s, connect
timeout, Monitoring override, radio off without Saved Networks)
- WifiService carries out the controller's actions, sets the EU
country code, and syncs the Clock over SNTP without touching the TZ
- Wi-Fi On/Off setting; Settings > Wi-Fi page: status, add from a scan
or a hidden network, forget
- Status Bar: W + signal bars, W? while searching, MON while monitoring
- Serial: wifi add / wifi status (replaces the step 1 heap probe)
Verified on the device: joins the test network ~5 s after boot, clock
set over NTP, ~129 KB free heap while connected.
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
- lib/apps_model (host-tested): SettingsMenu (rows, readable values,
choices, validation messages) and SetupWizard (names, Region
confirmation, timezone; saves only when finished)
- AppManager: modal Apps that Home/Back can't leave (setup wizard)
- SettingsApp: all settings plus Storage (usage, erase SD behind a
dialog) and About (version, node id, battery, memory, uptime) pages,
replacing the temporary Diagnostics App
- SetupApp: first-boot wizard, opened modally until SetupDone
- Node id and default names derived from the MAC like Meshtastic
- Widget demo is now hidden (About, then w)
- lib_ldf_mode = deep+ so libraries see each other's headers
Co-Authored-By: Claude Opus 5.5 <noreply@anthropic.com>
Claude-Session: https://claude.ai/code/session_01EhqxQ49eCju4CzKYNjZzwT
twislaandClaude Opus 5.5